Conectable directamente a PC para rápida configuración y toma de medidas
Resumen
The Granite™ Volt 108 easily expands the channel count on your data-acquisition system. It has eight differential or 16 single-ended input channels, as well as two excitation channels. The Volt 108 provides programmable, precision excitation for standard sensor measurements and power outputs for controlling sensors and peripherals. This module features a 24-bit, analog-to-digital converter with low-noise performance for superior analog measurements.
Ventajas y características
- 24-bit ADC and low-noise inputs for increased measurement quality
- Distributed data acquisition
- Channel count expansion via the CPI bus on Campbell Scientific data loggers
- Easier to program than traditional multiplexers
- Programmable noise rejection
- CANbus 2.0 A/B output available with the Extended Duty (-XD) version
- USB 2.0 interface for PC-based operation with Campbell Scientific Surveyor software
Imágenes
Preguntas frecuentes
Número de FAQs relacionadas con GRANITE VOLT 108: 8
Expandir todoDesplegar todo
Compatibilidad
Nota: lo siguiente muestra información de compatibilidad notable. No es una lista de todos los productos compatibles.
Dataloggers
| Producto | Compatible | Nota |
|---|---|---|
| CR1000X (retired) | Requires OS version 4 or greater. | |
| CR6 | Requires OS version 10 or greater. |
Miscelaneo
| Producto | Compatible | Nota |
|---|---|---|
| GRANITE 10 | Requires OS version 1 or greater. | |
| GRANITE 6 (retired) | Requires OS version 1 or greater. | |
| GRANITE 9 | Requires OS version 1 or greater. |
Información de compatibilidad adicional
The Volt 108 is compatible with CPI-enabled data loggers only.
Especificaciones
| Power Requirements | 9.6 to 32 Vdc voltage |
| Mounting | Standard 1-in. grid (DIN rail mounting available) |
| Accuracy |
|
| Number of Channels | 8 differential or 16 single-ended |
| Operating Temperature Range |
|
| Maximum Scan Rate |
|
| Input Range | ±5000 mV, ±1000 mV, and ±200 mV |
| Period Averaging | Traditional period averaging on analog input channels |
| CPI | For data logger connection. Baud rate selectable from 50 kbps to 1 Mbps. (Allowable cable length varies depending on baud rate, number of nodes, cable quality, and noise environment, but can be as long as 700 m under proper conditions.) |
| USB | USB 2.0 full speed connection available for attaching to a PC. (Port is used to configure the module and download updates via our Device Configuration Utility.) |
| Warranty | One year against defects in materials and workmanship |
| Dimensions | 20.3 x 12.7 x 5.1 cm (8 x 5 x 2 in.) |
| Weight | 0.8 kg (1.75 lb) |
Typical Current Drain |
|
| Sleep | <1 mA |
| Active 1 Hz Scan |
2 mA (estimated) Assumes one single-ended measurement with the first notch frequency (fN1) at 30 kHz Note: Any sensor excitation or switched power loads will be additive to this value. |
| Active 20 Hz Scan |
20 mA Assumes one single-ended measurement with the first notch frequency (fN1) at 30 kHz Note: Any sensor excitation or switched power loads will be additive to this value. |
| Active 1 kHz Scan |
67 mA Note: Any sensor excitation or switched power loads will be additive to this value. |
Voltage/Current Excitation Outputs |
|
| Voltage Excitation | ±5 V (@ 50 mA) |
| Current Excitation | ±2.5 mA (±5 V compliance voltage) |
| Number of Voltage/Current Excitation Outputs | 2 |
General Purpose Outputs |
|
| Number of SW5V Outputs | 2 |
| SW5V Output Resistance | 30 Ω |
| Number of SW12V Outputs | 1 |
| Typical Limit of SW12V Outputs | 200 mA |
| Minimum Limit of SW12V Outputs | 180 mA |
| Number of 12V Outputs | 1 |
| Typical Limit of 12V Outputs | 200 mA |
| Minimum Limit of 12V Outputs | 180 mA |
Documentos
Folletos producto
Misceláneo
Videos & Tutoriales
Descargas
CPI Calculator v.1.0 (2.49 MB) 06-07-2016
The CPI Calculator is a downloadable Microsoft Excel spreadsheet used to estimate the usage and capacity of a CPI network. The calculator provides an overview on CPI devices including the CDM-A108, CDM-A116, CDM-VW300, CDM-VW305, and the CSAT3B. The calculator can also estimate the measurement speed of the CDM-A108 and CDM-A116 based on the number of channels and measurement parameters.
The CPI Calculator is an estimation tool and will help you better understand and design CPI networks by considering the following:
- What is the capability of each CDM or CPI device
- What is the CPI network capacity
- How much of the CPI capacity are the CDMs or CPI devices using
Volt100 OS v.06.03 (640 KB) 09-05-2023
Execution of this download installs the Volt108 / Volt116 Operating System on your computer which can then be uploaded to the Volt108 or Volt116 device with the Device Configuration Utility.
Historial revisiones