Services Available |
---|
El NL120 permite al datalogger comunicar por TCP/IP en una LAN o conexión Internet dedicada. Este interface de comunicaciones pequeño y robusto se conecta en el puerto para periféricos de 40-pin disponible en el datalogger CR1000 y CR3000.
Leer másEl NL120 se conecta a un hub EtherNet 10baseT mediante el típico cable EtherNet directo. El cable debe ser cruzado si conectamos el NL120 directamente a la toma EtherNet de un ordenador. Dependiendo de la distancia, es importante que el cable esté apantallado.
La configuración del NL120 se hace mediante el software Device Configuration Utility (DevConfig). La aplicación DevConfig viene incluida en nuestros paquetes de software PC400, RTDAQ, y LoggerNet; y puede descargarse sin cargo de www.campbellsci.com/downloads
Número de FAQs relacionadas con NL120: 23
Expandir todoDesplegar todo
Yes, the NL120 can be repaired. Refer to the Repair and Calibration page for the process of returning equipment to Campbell Scientific.
The NL120 is a communications peripheral only. It does not provide additional analog terminals for a data logger.
Yes. The NL120 operates as transparent.
No. Configurations can be changed, however, via any other mode of communication with the datalogger.
No. The NL120 is used for one device only.
The following are some possible causes:
There is no separate firmware for the NL120. It is built into the main data logger’s operating system.
Alimentación | 12 V (supplied through the datalogger’s peripheral port) |
Ethernet Speed | 10Base-T (10 Mbps), half-duplex |
Typical Current Drain | 20 mA |
Dimensiones | 10.2 x 6.4 x 2.8 cm (4.0 x 2.5 x 1.1 in.) |
Peso | 66.62 g (2.35 oz) |
EMI and ESD Protection |
|
European Standards | Meets requirements for a class A device under European Standards. |
Application of Council Directive(s) | 89/336/EEC as amended by 89/336/EEC and 93/68/EEC |
Standards to Which Conformity Is Declared | EN55022-1; 1995 and EN50082-1: 1992 |
Software Requirements |
|
LoggerNet | Version 3.2 or later |
PC400 | Version 1.3 or later |
DevConfig | Version 1.5 or later |
Nota: lo siguiente muestra información de compatibilidad notable. No es una lista de todos los productos compatibles.
Producto | Compatible | Nota |
---|---|---|
CR1000 (retired) | ||
CR200X (retired) | ||
CR216X (retired) | ||
CR3000 (retired) | ||
CR5000 (retired) | ||
CR800 (retired) | ||
CR850 (retired) | ||
CR9000X (retired) |
Producto | Compatible | Nota |
---|---|---|
ENC10/12 | ||
ENC12/14 | Attached to a CR1000 | |
ENC14/16 | Attached to a CR1000 or CR3000 | |
ENC16/18 | Attached to a CR1000 or CR3000 |
El NL120 se conecta a un hub EtherNet 10baseT mediante el típico cable EtherNet directo. El cable debe ser cruzado si conectamos el NL120 directamente a la toma EtherNet de un ordenador. Para más de 2.75m de longitud, es importante que el cable esté apantallado.
El NL120 se conecta en el puerto para periféricos de 40-pin disponible en el datalogger CR1000 y CR3000. No es compatible con los dataloggers CR800, CR850, CR200X, CR5000, o CR9000X.