ENC16/18 Armario 457 x 406 x 228 mm
Robusto, versátil
Montaje fácil y seguro de equipos Campbell
meteorología aplicaciones agua aplicaciones energía aplicaciones flujo gas y turbulencia aplicaciones infraestructuras aplicaciones suelo aplicaciones

Resumen

El armario ENC16/18 es el modelo más grande que disponemos. En su interior podemos albergar un datalogger, fuente de alimentación y uno o más periféricos. Es habitual utilizarlo en aplicaciones que requieran una de nuestras baterías de tamaño grande y/o si es necesario fijar diversos periféricos de medida o control.

Leer más

Ventajas y características

  • Para uso en intemperie, y para proteger los instrumentos
  • Placa de montaje diseñada de forma que sea fácil fijar componentes Campbell Scientific
  • Armario color blanco, estabilizado UV que refleja la radiación solar—reduciendo los gradientes de temperatura dentro del armario sin necesidad de un protector para la radiación

Imágenes

Descripción detallada

The ENC16/18's backplate is prepunched with half-inch-on-center holes suitable for attaching a data logger, power supply, and a communications or measurement and control peripheral.

This enclosure is shipped with the 7363 enclosure supply kit that consists of desiccant, a humidity indicator card, cable ties, wire tie tabs, putty, grommets, screws, and PVC coupling. Additionally, Campbell Scientific offers a CS210 Enclosure Humidity Sensor for monitoring relative humidity inside of the enclosure. (See Ordering Info on the web page.)

Preguntas frecuentes

Número de FAQs relacionadas con ENC16/18: 17

Expandir todoDesplegar todo

  1. What can be done if an enclosure gasket becomes torn or damaged?

    If you purchased a Stahlin enclosure from Campbell Scientific and it has a failed gasket, we can help you. We will need you to provide an image of the failed gasket, verify the size of your enclosure, and provide your contact information. We can then arrange to have a replacement gasket sent to you from Stahlin. For assistance, contact Technical Support at 435.227.9100.

  2. What are the weight and internal dimensions of the ENC16/18?
    The ENC16/18 weighs 17 lb. Its internal dimensions are 16 x 18 x 9 in.
  3. Can an ENC16/18 be used with an enclosure heater to increase the inside temperature and reduce the risk of condensation?
    Yes. However, we do not sell the heaters.
  4. Can converters to 18 Vac and 12 Vdc be located within an ENC16/18 without affecting the datalogger or data?

    Most likely, yes. The datalogger is protected against electrical noise, and 60 Hz filtering can be selected in many sensor measurements to filter out the effects of 60 Hz noise.

  5. Can 120 Vac be brought into the ENC16/18?
    Yes. Use a standard electrical box and outlet.
  6. If the copper ground terminals attached to the bottom of an enclosure are oxidized and corroded, how can they be replaced?
    The terminals do not need to be replaced. Just sand or file the corrosion away, exposing clean copper, and the fittings will continue to be functional.
  7. Is a fiberglass enclosure suitable for an installation in a very cold location monitoring corrosion?
    Our fiberglass enclosures can withstand very cold locations, and their fiberglass/plastic construction is very resistant to corrosion.
  8. If the PVC fittings at the bottom of the enclosure have too small an inner diameter to accommodate all the cables passing through, is there a way to remove the PVC fittings?
    Unscrew the PVC fittings to remove them.
  9. How many mounting accessories should be ordered for each major device inside an enclosure?
    It depends on the device. Most devices have built-in mounting flanges, but some items require a separate mounting bracket.
  10. Does the enclosure have a mounting bracket inside to mount the datalogger?
    Yes. Each enclosure Campbell Scientific sells has a powder-coated backplate with holes on 1 in. centers that match the mounting flanges on our equipment for easy mounting.
Visite la librería de FAQ

Especificaciones

Color White (Reflects solar radiation, reducing temperature gradients inside the enclosure without using a separate radiation shield.)
Construction Fiberglass-reinforced polyester enclosure with door gasket, external grounding lug, stainless-steel hinge, and lockable hasps
Enclosure Classification NEMA 4X (before being modified for cable entry)
Number of Cable-Entry Seals 2 large, 2 medium, 2 small
Dimensions
  • 45.7 x 40.6 x 22.9 cm (18 x 16 x 9 in.) internal
  • 43.82 x 38.74 x 25.22 cm (17.25 x 15.25 x 9.93 in.) internal under the lid space
  • 49.53 x 44.4 x 26.98 cm (19.5 x 17.48 x 10.62 in.) external
Weight 7.7 kg (17 lb)

Compatibilidad

Nota: lo siguiente muestra información de compatibilidad notable. No es una lista de todos los productos compatibles.

Dataloggers

Producto Compatible Nota
CR1000 (retired)
CR200X (retired)
CR216X (retired)
CR300 (retired)
CR3000 (retired)
CR350
CR5000 (retired)
CR6
CR800 (retired)
CR850 (retired)
CR9000X (retired)

Miscelaneo

Producto Compatible Nota
21X (retired)
CR10X (retired)
CR23X (retired)
CR500 (retired)
CR510 (retired)
CR9000 (retired)

Información de compatibilidad adicional

The -VC cable opening option is required to fit a BP84 84-Ahr power supply in the ENC16/18 (see Ordering Info).

Casos de aplicación

argentina: measuring mountain weather conditions
Argentina: Measuring Mountain Weather Conditions
Introduction The Andes Mountains of Argentina are home to a rich and diverse group of organic......leer más
Explorar todos los Casos de Aplicación.