CS11-L AC Current Sensor
Measure the ac Current along an Electrical Wire
meteorología aplicaciones agua aplicaciones energía aplicaciones flujo gas y turbulencia aplicaciones infraestructuras aplicaciones suelo aplicaciones

Resumen

The CS11 monitors ac current along an electrical wire. It outputs a millivolt signal that many of our dataloggers can directly measure.

Leer más

Ventajas y características

  • Ideal applications include motor or generator load conditions, efficiency studies, intermittent fault detection, and rough submetering
  • Sensor is external to the wire jacket and has no direct electrical connection to the system

Imágenes

Top view
Top view
Top view
Bottom view

Descripción detallada

The CS11 uses CR Magnetic's CR8459 Current Transformer to detect the ac current along an electrical wire using the magnetic field that is generated by that current. The CS11 is external to the wire jacket and has no direct electrical connection to the system.

The CS11 is recommended for measurements that do not require high accuracy, such as motor or generator load condition monitoring, efficiency studies, intermittent fault detection, and rough submetering.

Preguntas frecuentes

Número de FAQs relacionadas con CS11-L: 5

Expandir todoDesplegar todo

  1. Connect the red wire to ground rather than its normal location on the CR200(X).

  2. No. The CS11-L is an ac-only sensor.

  3. Not directly. If the CS11-L is connected to a datalogger, the datalogger can take the ac measurement and control a solid-state relay based on some threshold within the datalogger program. The solid-state relay can then control other relays, solenoids, or motor starters. (Use of a solid-state relay is preferred because the datalogger can trigger it with a small 5 Vdc mA signal.)

  4. Yes. Three CS11-L sensors can be connected to a datalogger to measure the amperage on each of three phases.

  5. The following are some of the features of the CS11-L:

    • The quality of the measurements was improved by upgrading the 10 ohm internal resistor.
    • The CS11-L is compatible with the CR200(X)-series dataloggers, as well as all of the dataloggers that were compatible with the CS10-L. This allows the CS11-L to replace both the CS10-L and the CS15-L.
    • The programming examples were improved to give greater stability to the measurements. On some datalogger models, the ACPower() instruction can be used.

Especificaciones

Rango de medida 0.15 to 200 A (0.15 to 125 A for CR200X)
Frecuencia 50 and 60 Hz
Insulation Resistance 100 MΩ (@ 500 Vdc)
High Potential 2000 V
Rated Current 200 A, 125 A (CR200X)
Precisión Typically ±1% of actual value with provided multiplier (with 10 Ω maximum burden [resistive])
Multiplier iMult=200 A/1000 mV=0.2
Rango temperatura funcionamiento -25° to +55°C
Rango temperatura almacenamiento -25° to +70°C
Case Material Polypropylene resin
Construction Epoxy encapsulated
Inner Diameter 1.9 cm (0.75 in.)
Outer Diameter 4.8 cm (1.89 in.)
Height 1.7 cm (0.67 in.)

Compatibilidad

Nota: lo siguiente muestra información de compatibilidad notable. No es una lista de todos los productos compatibles.

Dataloggers

Producto Compatible Nota
CR1000 (retired)
CR1000X
CR300 (retired)
CR3000 (retired)
CR310
CR350
CR6
CR800 (retired)
CR850 (retired)

Documentos

Casos de aplicación

Egypt: Preserving King Tut's Tomb
In 1922, when the tomb of Tutankhamen was discovered in Egypt's Valley of the Kings,......leer más

Artículos y notas de prensa