Este producto ya no está disponible y ha sido reemplazado por: VOLT116. Algunos accesorios, recambios o servicios pueden todavía estar disponibles.
| Services Available |
|---|
Resumen
El CDM-A116 es un módulo de entradas analógicas que permite fácilmente expandir el número de canales de entrada analógicos de nuestros dataloggers Campbell Scientific. El CDM-A116 contiene un conversor A/D de 24-bit, y un front-end de bajo ruido que proporciona medidas analógicas excepcionales. Este módulo permite también promediar períodos y dispone de canales de excitación en voltaje y corriente para alimentar puentes de medida.
El CDM-A116 tiene 16 canales de entrada diferenciales y 4 canales de excitación. Dispone de terminales 12V, dos de 12V conmutables para alimentar periféricos, y cuatro terminales de 5V conmutables para control de periféricos.
Leer másVentajas y características
- Ability to make simultaneous measurements
- CANbus 2.0A/2.0B capable; contact Campbell Scientific for details
Imágenes
Descripción detallada
The CDM-A116 offers 24-bit sigma-delta Adc with 16 user programmable notch frequencies from 30,000 Hz to 2.5 Hz, including 50 and 60 Hz. Previous generations of data loggers could notch out 50 or 60 Hz.
Especificaciones
| -NOTE- | Additional specifications are listed in the CDM-A108 and CDM-A116 brochure. |
| Mounting | Standard 1-in. grid (DIN rail mounting available) |
| Operating Temperature |
|
| Power Requirements | 9.6 to 32 Vdc voltage |
| Estimated Accuracy |
|
| Number of Channels | 16 differential or 32 single-ended inputs |
| Analog Inputs | 32 single-ended or 16 differential (with ±5000 mV, ±1000 mV, ±200 mV ranges 24 bit ADC) |
| Maximum Multiplexed Sample Rate | 3.0 kHz (using fast [100 μs] input setting) |
| Maximum Burst Sample Rate | 30 kHz |
| Input Range | ±5000 mV, ±1000 mV, and ±200 mV |
| Period Averaging | Traditional period averaging on analog input channels |
| CPI | For data logger connection. Baud rate selectable from 50 kbps to 1 Mbps. (Allowable cable length varies depending on baud rate, number of nodes, cable quality, and noise environment, but can be as long as 700 m under proper conditions.) |
| USB | USB 2.0 full speed connection available for attaching to a PC. (Port is used to configure the module and download updates via our Device Configuration Utility.) |
| Warranty | One year against defects in materials and workmanship |
| Dimensions | 20.3 x 12.7 x 5.1 cm (8 x 5 x 2 in.) |
| Weight | 0.9 kg (1.95 lb) |
Typical Current Drain |
|
| Sleep | <1 mA |
| Active 1 Hz Scan |
2 mA (estimated) Assumes one single-ended measurement with the first notch frequency (fN1) at 30 kHz |
| Active 20 Hz Scan |
20 mA Assumes one single-ended measurement with the first notch frequency (fN1) at 30 kHz |
Voltage/Current Excitation Outputs |
|
| Voltage Excitation | ±5 V (@ 50 mA) |
| Current Excitation | ±2.5 mA (±5 V compliance voltage) |
| Number of Voltage/Current Excitation Outputs | 4 |
General Purpose Outputs |
|
| Number of SW5V Outputs | 4 |
| SW5V Output Resistance | 30 Ω |
| Number of SW12V Outputs | 2 |
| Typical Limit of SW12V Outputs | 200 mA |
| Minimum Limit of SW12V Outputs | 180 mA |
| Number of 12V Outputs | 2 |
| Typical Limit of 12V Outputs | 200 mA |
| Minimum Limit of 12V Outputs | 180 mA |
Compatibilidad
Nota: lo siguiente muestra información de compatibilidad notable. No es una lista de todos los productos compatibles.
Dataloggers
| Producto | Compatible | Nota |
|---|---|---|
| CR1000 (retired) | To use the CDM-A116 with a CR1000 datalogger, an SC-CPI (data-logger-to-CPI interface) must be used between the data logger and the CDM-A116. | |
| CR1000X | ||
| CR300 (retired) | ||
| CR3000 (retired) | To use the CDM-A116 with a CR3000 datalogger, an SC-CPI (data-logger-to-CPI interface) must be used between the data logger and the CDM-A116. | |
| CR310 | ||
| CR6 | ||
| CR800 (retired) | To use the CDM-A116 with a CR800 datalogger, an SC-CPI (data-logger-to-CPI interface) must be used between the data logger and the CDM-A116. | |
| CR850 (retired) | To use the CDM-A116 with a CR850 datalogger, an SC-CPI (data-logger-to-CPI interface) must be used between the data logger and the CDM-A116. |
Miscelaneo
| Producto | Compatible | Nota |
|---|---|---|
| GRANITE 9 |
Documentos
Folletos producto
Manuales
Descargas
CDM-A100 OS v.06.03 (606 KB) 09-05-2023
Execution of this download installs the CDM-A108 / CDM-A116 Operating System on your computer which can then be uploaded to the CDM-A108 or CDM-A116 device with the Device Configuration Utility.
Historial revisionesCPI Calculator v.1.0 (2.49 MB) 06-07-2016
The CPI Calculator is a downloadable Microsoft Excel spreadsheet used to estimate the usage and capacity of a CPI network. The calculator provides an overview on CPI devices including the CDM-A108, CDM-A116, CDM-VW300, CDM-VW305, and the CSAT3B. The calculator can also estimate the measurement speed of the CDM-A108 and CDM-A116 based on the number of channels and measurement parameters.
The CPI Calculator is an estimation tool and will help you better understand and design CPI networks by considering the following:
- What is the capability of each CDM or CPI device
- What is the CPI network capacity
- How much of the CPI capacity are the CDMs or CPI devices using
Device Configuration Utility v.2.30 (46.9 MB) 02-10-2024
A software utility used to download operating systems and set up Campbell Scientific hardware. Also will update PakBus Graph and the Network Planner if they have been installed previously by another Campbell Scientific software package.
Supported Operating Systems:
Windows 11 or 10 (Both 32 and 64 bit)
Casos de aplicación
The Oklahoma Mesonet is a statewide environmental monitoring network developed through the cooperative efforts of......leer más