Resumen
The 4WFBS120 is a four-wire, full-bridge module that provides completion resistors for a strain gage or other sensor that acts as a single variable resistor. This module should be used to measure sensors that have a 120-ohm nominal resistance.
Leer másVentajas y características
- Fácil de instalar o quitar
- Se conecta directamente en los terminales de entrada del datalogger
- Compatible con la mayoría de dataloggers Campbell Scientific
Imágenes
Descripción detallada
The 4WFBS120 completes a full Wheatstone bridge. It can also be used to complete the back half of a Wheatstone bridge for use in a ¼ bridge strain circuit (one active element) using a dummy gage, or in a ½ bridge strain circuit (two active elements). The Wheatstone bridge circuit converts small changes in resistance to an output voltage that our dataloggers can measure.
The 4WFBS120 includes two external pins that allow customers to perform shunt calibrations, which are used to correct for sensitivity errors.
4-Wire Full Bridge Module Schematic
(R4=120 Ω for the 4WFBS120)
4WFBS120-to-Sensor Hookup
Productos similares
Preguntas frecuentes
Número de FAQs relacionadas con 4WFBS120: 5
Expandir todoDesplegar todo
-
The CR1000 excitation channel current limit is 25 mA at 2500 mV. Using 120 ohm gages with multiple 4WFBS120 modules, only two gages can be hooked up for each excitation channel with 2500 mV excitation. If three gages per excitation channel are used, the excitation needs to be reduced to approximately 1750 mV.
-
Each datalogger has specific excitation current sourcing capability. It is imperative not to exceed this current limit when trying to excite multiple strain gages from the same excitation channel.
- The equivalent resistance of the 4WFBS120 is 214.285 ohm. If the circuit is being excited with 2.5 V (2500 mV), it will draw 11.67 mA (2500 mV / 214.285 ohm = 11.67 mA).
- The equivalent resistance of the 4WFBS350 is 518.518 ohm. If the circuit is being excited with 2.5 V (2500 mV), it will draw 4.82 mA (2500 mV / 518.518 ohm = 4.82 mA).
- The equivalent resistance of the 4WFBS1K is 1000.00 ohm. If the circuit is being excited with 2.5 V (2500 mV), it will draw 2.5 mA (2500 mV / 1000 ohm = 2.5 mA).
-
More than one strain gage sensor can use the same excitation terminal if the bridge resistance is high enough or the excitation voltage is limited. The limit is determined by the current capacity of the excitation terminal (25 mA at 2.5 V) and the equivalent resistance of the circuit.
-
The ST350 is designed as a full-bridge strain transducer with four active elements that can be directly connected to a datalogger (or a multiplexer connected to a datalogger) without adding a completion module such as the 4WFBS350 or 4WFBS120.
-
To make strain gage measurements, a terminal input module is needed. It is necessary to match the resistance of the strain gage with the resistance of the terminal input module.
- For a 120 ohm strain gage, use the 4WFBS120.
- For a 350 ohm strain gage, use the 4WFBS350.
- For a 1000 ohm (1 kohm) strain gage, use the 4WFBS1K.
Especificaciones
| Used With | 4-wire strain gages or other full bridge measurements that have a 120 Ω nominal resistance |
| Dimensions | 1.5 x 1.5 x 2.7 cm (0.6 x 0.6 x 1.0 in.) for body with prongs |
| Weight | 6 g (0.2 oz) |
2:1 Resistive Divider |
|
| Resistance | 1 kΩ/1 kΩ |
| Tolerance | Ratio: ±0.01% (@ 25°C) |
| Maximum Temperature Coefficient | Ratio: 0.5 ppm/°C (-55° to +85°C) |
| Power Rating | 0.1 W (@ 70°C) per element |
Completion Resistor (bulk metal foil) |
|
| Resistance | 120 Ω |
| Tolerance | ±0.01% (@ 25°C) |
| Maximum Temperature Coefficient | 0.8 ppm/°C |
| Power Rating | 0.25 W (@ 70°C) |
Compatibilidad
Nota: lo siguiente muestra información de compatibilidad notable. No es una lista de todos los productos compatibles.
Dataloggers
| Producto | Compatible | Nota |
|---|---|---|
| CR1000 (retired) | ||
| CR200X (retired) | ||
| CR216X (retired) | ||
| CR300 (retired) | ||
| CR3000 (retired) | ||
| CR310 | ||
| CR350 | ||
| CR5000 (retired) | ||
| CR6 | ||
| CR800 (retired) | ||
| CR850 (retired) |
Miscelaneo
| Producto | Compatible | Nota |
|---|---|---|
| 21X (retired) | ||
| CR10 (retired) | ||
| CR10X (retired) | ||
| CR23X (retired) | ||
| CR500 (retired) | ||
| CR510 (retired) | ||
| CR9050 (retired) |
Información de compatibilidad adicional
Multiplexers
The 4WFBS120 is compatible with our multiplexers.
Data Logger Considerations
The 4WFBS120 uses one differential analog input; an adjacent analog ground channel accepts the "ground prong" of the 4WFBS120. Not all data logger terminal strips have this sequence on all channels, so please check your data logger's wiring panel to confirm channel assignments, especially if you plan to use multiple Terminal Input Modules.
The lead wire that emanates from the head of the 4WFBS120 connects to a data logger excitation channel.
Please note that if a CR10X will be used to measure thermocouples in the same application, newer CR10X Wiring Panels and the CR10XTCR Reference Thermistor (with its accompanying Thermocouple Cover) are deep enough to cover the data logger input channels with a Terminal Input Module attached; older CR10TCRs are not deep enough.
Programming
The 4WFBS120 is measured with the BrFull Instruction in CRBasic, and with Instruction 6 (Full Bridge) in Edlog.