SC12 Robust CS I/O Cable, 2 ft
2-Peripheral Connector Cable for Data Loggers
meteorología aplicaciones agua aplicaciones energía aplicaciones flujo gas y turbulencia aplicaciones infraestructuras aplicaciones suelo aplicaciones

Resumen

The SC12 is our standard cable for connecting the data logger's 9-pin serial I/O port to most peripherals with a 9-pin port. It is supplied with many of our standard communications peripherals.  Its 9-pin pin (male) connector attaches to the data logger's CS I/O port, and the two 9-pin socket (female) connectors can attach to peripherals or interfaces.

Leer más

Ventajas y características

  • Provides one 9-pin pin (male) connector and two 9-pin socket (female) connectors
  • Included with many of our standard communication peripherals
  • Formerly known as "the little blue ribbon cable"

Imágenes

Descripción detallada

The SC12 has one 9-pin pin (male) connector that attaches to the data logger's CS I/O port and two 9-pin socket (female) connectors that can attach to peripherals with a 9-pin RS-232 port. Additional peripherals can be connected by attaching one of the two socket (female) connectors with the pin (male) connector of an additional SC12 cable. The SC12 is compatible with any data logger that has a CS I/O port.

Prior to June 2003, the SC12 was a ribbon cable. On June 18, 2003, Campbell Scientific began shipping a redesigned SC12 cable. The redesigned SC12 is a black molded cable that is more rugged and resistant to chemicals than the original ribbon cable. Although the two cables are largely interchangeable, the new black version is not compatible with the ET107 and some of our older products (see Compatibility).

The redesigned SC12 cable has resulted in the obsolescence of the SC12R cable. However, the SC12R-6 cable will continue to be available. The SC12R-6 features a six foot length for applications where the peripherals must be separated by several feet.

Preguntas frecuentes

Número de FAQs relacionadas con SC12: 2

  1. What would happen if two dataloggers were connected directly through CS I/O ports via an SC12 cable?

    Nothing. An unmodified SC12 cable does not allow for this type of connection; it provides a connection for one datalogger and two CS I/O peripherals.

  2. What is the pinout for the SC12 cable?

    The SC12 cable is just pin-to-pin 1 through 9 and shell-to-shell, similar to a typical RS-232 cable. However, the SC12 cable uses a twisted pair to connect pin 1 to 1 and pin 2 to 2. The rest of the pins are connected using straight, unpaired conductors. The cable drain wire is used to connect the metal shells.

Visite la librería de FAQ

Especificaciones

Connectors One 9-pin pin (male), two 9-pin socket (female)
Length 66.0 cm (26.0 in.)
Weight 45 g (2 oz)

Compatibilidad

Nota: lo siguiente muestra información de compatibilidad notable. No es una lista de todos los productos compatibles.

Dataloggers

Producto Compatible Nota
CR200X (retired)
CR216X (retired)
CR5000 (retired)

Miscelaneo

Producto Compatible Nota
CR9000 (retired)

Información de compatibilidad adicional

Peripherals

The SC12 is shipped with many of our standard communication peripherals (see Overview). Retired products that are compatible with this cable include the COM200, COM210, COM310, COM300, CR10KD, COM100, SAT ARGOS, ST-20, SAT HDR GOES, CR56, DC112, DC1765, DC95, RF95, SC232, SC32A, SC532, SC932, SC95A, SDC-RF, SM16, SM192, SM64, SM232A, SM716, [HSVM100], VS1, CSM1, DSP4.

The newer black-molded SC12 cable is not compatible with the ET107, PS512M, CH512R, MetData1, or SDS511.

Data Logger Considerations

The SC12 is compatible with any data logger with a nine-pin CS I/O port.