Services Available |
---|
El interface de red NL200 permite que los dataloggers Campbell Scientific comuniquen por TCP/IP en una LAN o conexión Internet dedicada. Puede conectarse en el puerto CS I/O o RS-232 del datalogger.
Es un dispositivo compatible con un enlace de comunicaciones Ethernet 10/100 Mbps. Incluye puertos de comunicaciones CS I/O y RS-232. Dispone de puerto USB para configuración.
Utilizando el puerto CS I/O del NL200, se puede configurar en modo "bridge Ethernet" de forma que se abre el acceso a la funcionalidad IP interna (stack TCP/IP) del datalogger CR800/850, CR1000, y CR3000 (por ej. acceso página web del datalogger, envío/recepción emails, transferencia de ficheros FTP). De forma alternativa, el NL200 se puede configurar para que actúe como Serial Server y/o router PakBus. Adicionalmente, el NL200 puede actuar como TLS Proxy Server.
Número de FAQs relacionadas con NL200: 1
The maximum recommended segment length (length of cable between the NL device and the Ethernet repeater, hub, switch, or router it is connected to) for 10Base-T and 100Base-Tx networks using CAT5e cable is 100 m.
Conector alimentación | DC Barrel |
Alimentación | 7 to 20 Vdc (not powered via CS I/O or USB) |
Rango temperatura funcionamiento | -25° to +50°C |
Configuración |
|
CS I/O Port | SDC 7, 8, 10, or 11 (does not support ME) |
RS-232 Port | DTE |
USB Port | Micro-B |
Ethernet Port | IEEE 802.3, Auto-MDIX, IPv4, TCP, DHCP, Ping, Telnet, TLS, PakBus |
Conformidad |
|
Application of Council Directive(s) | 2004/108/EC |
Standards to Which Conformity Is Declared | EN61326-1;2006 |
Connections/Routes Supported |
|
Dimensiones | 16 x 6.73 x 2.54 cm (6.3 x 2.65 x 1 in.) |
Peso | 177 g (6.3 oz) |
Consumo |
|
Activo | 50 mA (@ 13 Vdc) |
Forced Standby | 2 mA (available when using Ethernet-to-CS I/O Bridge Mode) |
Communication Rate |
|
RS-232 DTE Port | 1200 to 115.2k bps |
CS I/O Port | 9600 to 460.8k bps |
Ethernet | 10/100 Mbps |
Data Logger | Serial Server | PakBus Router | Bridge Mode |
CR200(X) Series | |||
CR800/CR850 | |||
CR1000 | |||
CR3000 | |||
CR5000 | |||
CR9000X | * | ||
CR6 | |||
CR510-PB | |||
CR10X-PB | |||
CR23X-PB | |||
Mixed-Array |
** |
Notes:
* Although compatible, the CR9000X does not need an Ethernet interface because it has an on-board Ethernet port.
** It is possible to use an NL200 to connect to a mixed-array data logger (e.g., CR10, CR10X, CR23X, 21X, CR7) by using an SC32B between the data logger's CS I/O port and the NL200's RS-232 port.
Current NL200 / NL201 firmware. Requires the Device Configuration Utility and a USB micro cable.
Note: When updating to OS 10.03 from OS 6 or previous, settings will be reinitialized to factory defaults. When updating to OS 10.03 from OS 7, settings will be retained.